Search
Products
Paper-Faced Inside Corner Bead
Provides incredibly straight and smooth inside 90° corners for drywall finishing
Rigid steel-reinforced inside corners provide a durable guide to achieve exceptionally straight and sharp inside…
Paper-Faced Corner Bead
Lowering Labor Costs by removing one coat of compound
Paper-faced tape-on beads combine galvanized metal corner and edge protection with high-grade paper to provide cost-effective,…
Paper-Faced Inside Splayed Corner Bead
Used to create a sharp, crisp line for finishing inside off-angle or inverted splayed corners
Off-angle tape-on 120/135° inside or reverse splayed bead is used to achieve a crisp, clean, straight…
Paper-Faced Bullnose Tape-on
Creates elegant, rounded outside drywall corners adding contemporary styling and a sense of openness to any room
3/4" tape-on bullnose corner bead is used to create a smooth, rounded look to…
Rip-Bead® Shadow Reveal
Create 3/16" to 1" reveals in drywall & veneer surfaces
Creates edge reveal when butting up to ceilings, base trim and other finished interior components.
Shadow Reveal
Create 1/2" to 3/4" reveals in drywall & veneer surfaces
Creates edge reveal when butting up to ceilings, base trim and other finished interior components.
Channel Reveal
Create 1/4" to 2" reveals in drywall surfaces
No backing or blocking needed.
"V" Channel Reveal
Create a modern look and shadowing effect
Designed with a dramatic, deep "V" reveal.
Soffit Vent Control Joint Combination
Continuous, one-piece, combination design like a control joint
Allowing movement of the plaster with a vent area that has a perforated flange to assist with embedment.
"F" Series Control Joint and Vent
Designed to work on narrow overhangs
Where vents are needed to go against fascia or walls.
Soffit Vent with J-Flange
J-bead flanges cover the raw edges of soffit board
One-piece soffit vents provide an economical means for venting soffit areas. Vent clips are provided for proper connection and alignment of the…
Miscellaneous Soffit Vent
One-piece Soffit Vent designed for plywood, soffit board, and three-coat stucco
May be combined with Starter Strips / Casing Beads or DEFS Casing Beads.
Surface Mount Soffit Vent
One-piece soffit board designed for venting soffit areas over exterior board in EIFS and DEFS applications
Available with 2", 3", 4" wide vents, each with a 1/8” ground. Vent clips are provided to…
Soffit Vent with Perforated Flanges
Provides an economical means for venting soffit areas
One-piece soffit vent with perforated flanges to assist in embedment of the base coat mixture and to cover the raw edges of the soffit board.…
Soffit Drip - Surface Mount
Designed for exterior soffits where a drip screed and an edge reveal need to be combined
Used to direct moisutre away from the installation in EIFS and DEFS installations. Always use a rigid backing…
Soffit Drip - Pre-Installed
Designed for exterior soffits where a drip screed and edge reveal need to be combined
Pre-installed soffit edge reveals with a drip edge to direct moisture away from the installation.
Sloped Sill Wedge
Trim component used to provide a slope over the sill to direct intruding water to the outside of the weather-resistive barrier
This is not a flashing; it is intended for use in combination with…
Channel Reveal (with perforated flanges)
Create 1/4" to 2" reveals in stucco and plaster surfaces
Clips are provided for alignment and as a base for sealants.
Drip Screed Reveals
Designed for stucco or plaster soffits when a drip and reveal need to be combined
To assist with moving moisture away from the wall.
Soffit Vents (One-Piece)
Continuous one-piece Soffit Vent
Reinforcing rib to key into stucco and plaster with a perforated flange.
Soffit Vents (One-Piece with Edge Clip)
Continuous one-piece Soffit Vent
Reinforcing rib to key into stucco and plaster. Vertical edge clips are provided for special installations.
Soffit Vents (Two-Piece Narrow Overhang)
Continuous two-piece Soffit Vent
For stucco and plaster with vertical edge clips provided for special installations.
FCS Soffit Vent
Available in several grounds and widths
Can be ordered with the 300VFZ clip for installation.
Vented Drip Screed
Designed to address finishing the plaster to the vertical soffit area intersection
When a drip and soffit vent need to be combined.
"F" Channel Reveal
Create 1/4" to 1" reveals in drywall surfacesDesigned to be used at the juncture of door jambs, windows and other unfinished surfaces.
"F" Channel Reveals
Forms 1/2" to 2" reveals in wall and ceiling designsFormed at the juncture of dissimilar materials.
Factory Fabricated Channel Reveals
Create clear channel designs for drywall surfacesAll intersections are manufactured in a controlled factory environment to the highest quality standards.
Soffit Vents (Three-Piece with Edge Clip)
Continuous three-piece Soffit VentFor stucco and plaster.
Soffit Vents (Three-Piece)
Continuous three-piece Soffit VentFor stucco and plaster.
"F" Series Architectural Soffit Vent
AFCS Series of one-piece soffit vent with a reinforcing rib to key into stucco3/4" elongated vent holes.
Architectural Soffit Vent
Series of one-piece soffit vent with a reinforcing rib to key into stucco3/4" elongated vent holes.