Search
Products
Soffit Vent Control Joint Combination
Continuous, one-piece, combination design like a control joint
Allowing movement of the plaster with a vent area that has a perforated flange to assist with embedment.
"F" Series Control Joint and Vent
Designed to work on narrow overhangs
Where vents are needed to go against fascia or walls.
Vinyl 3-1/2" Drip Screed w/ Weep Holes and Tape
Relieves moisture from stucco
The DS15-78-25WX is a combination Drip Screed with Casing Bead and Control Joint for use in stucco plane transitions. Install on frame construction for use in…
Soffit Vent with J-Flange
J-bead flanges cover the raw edges of soffit board
One-piece soffit vents provide an economical means for venting soffit areas. Vent clips are provided for proper connection and alignment of the…
Miscellaneous Soffit Vent
One-piece Soffit Vent designed for plywood, soffit board, and three-coat stucco
May be combined with Starter Strips / Casing Beads or DEFS Casing Beads.
Surface Mount Soffit Vent
One-piece soffit board designed for venting soffit areas over exterior board in EIFS and DEFS applications
Available with 2", 3", 4" wide vents, each with a 1/8” ground. Vent clips are provided to…
Soffit Vent with Perforated Flanges
Provides an economical means for venting soffit areas
One-piece soffit vent with perforated flanges to assist in embedment of the base coat mixture and to cover the raw edges of the soffit board.…
Soffit Drip - Pre-Installed
Designed for exterior soffits where a drip screed and edge reveal need to be combined
Pre-installed soffit edge reveals with a drip edge to direct moisture away from the installation.
Vented Shadow Reveal
Designed for ceilings when a vented reveal is required at the juncture of a wall and ceiling where horizontal movement may occur
Vent clips are provided to connect reveal sections and to assist in…
Vented Channel Reveal - Surface Mount
Vented Channel Reveals facilitate perimeter air flow to assist in moisture management and temperature control
This vent is intended for surface-mount applications. Always use a rigid backing or…
Architectural Vented Channel Reveal - Surface Mount
A variation on the vented channel reveal for when the design style calls for a different aesthetic
The slots function in the same way as the holes on a standard Vented Channel Reveal, allowing air…
Vented "F" Channel Reveal - Surface Mount
"F" Channel Reveals provide a reveal at the juncture of walls, ceilings, or dissimilar materials
Perforated flanges allow the base coat mixture to easily flow through and bond with the substrate.
Architectural Vented "F" Channel Reveal - Surface Mount
"F" Channel Reveals provide a reveal at the juncture of walls, ceilings, or dissimilar materials
Perforated flange allow the base coat mixture to easily flow through and bond with the substrate.
Drip Casing
Drip leg directs moisture away from openings and foundation walls
Designed to be used above window and door openings or at the foundation line to assist with moving moisture away from the wall. May…
Drip Flashing - 3" and 3-1/2" Flange
Designed to be used above window and door openings or at the foundation line
To assist with moving moisture away from the wall.
Truss Spacer / Bracer
TRUSS SPACER / BRACER
The Truss Spacer/Bracer is used for lateral bracing and spacing of trusses 24 inches on center.
Load Share Clip (CDLSC)
LOAD SHARE CLIP
The CDLSC load share clip series is manufactured to transfer loads between two truss or framing ply members made of solid sawn or structural composite lumber.
Hurricane Anchor Clips
HURRICANE ANCHOR CLIPS
The CDHTHA anchor series is manufactured to attach metal plate connected trusses, framing members and wall members, made of solid sawn or structural composite lumber; to solid…
Hurricane Tie (CDHT2A, 2.5A, 2.5T, 3)
HURRICANE tie
Used as a connection between truss/rafters and walls to resist lateral and uplift conditions.
Hurricane Tie (CDHT6, 8)
HURRICANE tie
Used as a connection between truss/rafters and walls to resist lateral and uplift conditions.
Hurricane Tie (CDHT1, 10A, 10S)
HURRICANE tie
Designed to hold trusses on both sides to transfer uplift loads from roof framing members to the wall studs.
Soffit Vents (One-Piece)
Continuous one-piece Soffit Vent
Reinforcing rib to key into stucco and plaster with a perforated flange.
Soffit Vents (One-Piece with Edge Clip)
Continuous one-piece Soffit Vent
Reinforcing rib to key into stucco and plaster. Vertical edge clips are provided for special installations.
Soffit Vents (Two-Piece Narrow Overhang)
Continuous two-piece Soffit Vent
For stucco and plaster with vertical edge clips provided for special installations.
FCS Soffit Vent
Available in several grounds and widths
Can be ordered with the 300VFZ clip for installation.
Vented Drip Screed
Designed to address finishing the plaster to the vertical soffit area intersection
When a drip and soffit vent need to be combined.
Soffit Vents (Three-Piece with Edge Clip)
Continuous three-piece Soffit VentFor stucco and plaster.
Soffit Vents (Three-Piece)
Continuous three-piece Soffit VentFor stucco and plaster.
BackerBead® Drip Flashing - 3-1/2" Flange
Drip flashing with built-in closed cell backer rodBackerBead® Drip Flashing - 3-1/2" Flange is designed to provide positive drainage above exterior window and door openings while also providing a…
"F" Series Architectural Soffit Vent
AFCS Series of one-piece soffit vent with a reinforcing rib to key into stucco3/4" elongated vent holes.
Architectural Soffit Vent
Series of one-piece soffit vent with a reinforcing rib to key into stucco3/4" elongated vent holes.
Archmaker™ Drip Flashing - 2" Flange
Designed to be used above window and door openings or at the foundation lineTo assist with moving moisture away from the wall.