Search
Products
BackerBead® Drip Flashing - 3-1/2" Flange
Drip flashing with built-in closed cell backer rodBackerBead® Drip Flashing - 3-1/2" Flange is designed to provide positive drainage above exterior window and door openings while also providing a…
Drip Casing
Drip leg directs moisture away from openings and foundation wallsDesigned to be used above window and door openings or at the foundation line to assist with moving moisture away from the wall. May be…
Drip Flashing - 3" and 3-1/2" Flange
Designed to be used above window and door openings or at the foundation lineTo assist with moving moisture away from the wall.
Vinyl 3-1/2" Drip Screed w/ Weep Holes and Tape
Relieves moisture from stuccoThe DS15-78-25WX is a combination Drip Screed with Casing Bead and Control Joint for use in stucco plane transitions. Install on frame construction for use in…
Soffit Drip - Pre-Installed
Designed for exterior soffits where a drip screed and edge reveal need to be combinedPre-installed soffit edge reveals with a drip edge to direct moisture away from the installation.
Furring Channel / Hat Channel
Furring Channel for Walls and CeilingsEconomical hat-shaped framing component used to “furr” out ceilings and masonry walls.
L-Angle / Corner Angle
L-angle / corner angle
Non-structural corner angles commonly used to connect, reinforce or secure metal stud framing in various drywall applications.
Structural L-Angle commonly used for connection…
U-Channel (CRC)
Traditional cold-rolled Channel (CRC) for bridging
ClarkDietrich U-Channel or Cold Rolled Channel (CRC) are one of the most common bridging methods used to provide resistance to stud rotation and…
Structural Studs
ClarkDietrich Cold-Formed Steel C-Studs (C-Series™)Cold-Formed / Light-Gauge C-shaped framing members for axial load-bearing walls, curtain walls, tall interior partitions, floor joists and roof…
Structural Track
ClarkDietrich Cold-Formed Steel TrackU-shaped channel runners used as the top and bottom tracks to secure wall studs or end support closures for floor joist framing. Structural Steel Track can be…
Load Share Clip (CDLSC)
LOAD SHARE CLIPThe CDLSC load share clip series is manufactured to transfer loads between two truss or framing ply members made of solid sawn or structural composite lumber.
Hurricane Anchor Clips
HURRICANE ANCHOR CLIPSThe CDHTHA anchor series is manufactured to attach metal plate connected trusses, framing members and wall members, made of solid sawn or structural composite lumber; to solid…
Hurricane Tie (CDHT2A, 2.5A, 2.5T, 3)
HURRICANE tieUsed as a connection between truss/rafters and walls to resist lateral and uplift conditions.
Hurricane Tie (CDHT6, 8)
HURRICANE tieUsed as a connection between truss/rafters and walls to resist lateral and uplift conditions.
Hurricane Tie (CDHT1, 10A, 10S)
HURRICANE tieDesigned to hold trusses on both sides to transfer uplift loads from roof framing members to the wall studs.
Drip Flashing for Rainscreen - DFLRS
Designed to be used at the bottom of entangled mesh rainscreens.
Truss Spacer / Bracer
TRUSS SPACER / BRACERThe Truss Spacer/Bracer is used for lateral bracing and spacing of trusses 24 inches on center.
Archmaker™ Drip Flashing - 2" Flange
Designed to be used above window and door openings or at the foundation lineTo assist with moving moisture away from the wall.
PanelTRAK
Steel Track for direct web bearingPanelTRAK is a structural steel track that allows steel studs to bear directly on the track web rather than the radii of the track corners. Because…