Search
Products
Strait-Flex® Arch-Stick
composite arched corner BEAD
Designed for outside 90° arched corners, eliminating flat spots.
Strait-Flex® Big-Stick
Designed for high traffic, outside 90° cornersThe easiest corner bead on the market to install and repair.
Strait-Flex® Medium
Finishes INSIDE 90° AND OFF-ANGLE CORNERS
Strait-Flex Medium is a high-performance drywall corner bead.
Strait-Flex® Arch-Flex
DESIGNED FOR COMPOUND ARCHES AND DOUBLE CURVE APPLICATIONS
Arch-Flex is designed for compound arches and double curve applications, including arched windows and doors, ceilings, soffits, staircases…
Rip-Bead® Shadow Reveal
Create 3/16" to 1" reveals in drywall & veneer surfaces
Creates edge reveal when butting up to ceilings, base trim and other finished interior components.
Shadow Reveal
Create 1/2" to 3/4" reveals in drywall & veneer surfaces
Creates edge reveal when butting up to ceilings, base trim and other finished interior components.
Strait-Flex® Edge-Tape
Designed to replace tear-off beadEdge-Tape creates clean, straight edges, is twice as fast, and uses half the compound compared to tear-off bead.
Strait-Flex® Butt-Tape
Designed for fast, flat, butt-jointsVertical and horizontal butt-joints and commercial “Top-Out” applications.
Strait-Flex® X-Crack
Framing AlignmentEliminates ceiling cracks and straightens uneven framing.
Can-Patch (Commercial)
Can light patch (commercial)Pre-cut 6-1/4" hole fits standard commercial ceiling lights and can light receptacles.
Can-Patch (Residential)
Can light patch (residential)Pre-cut 6-1/4" hole fits standard residential ceiling lights and can light receptacles.
EIFS/DEFS Corner Bead
Designed for use in EIFS and DEFS wall and ceiling systemsThese corner beads are hard to damage, rust-proof, and straight.
Soffit Vent with J-Flange
J-bead flanges cover the raw edges of soffit boardOne-piece soffit vents provide an economical means for venting soffit areas. Vent clips are provided for proper connection and alignment of the…
Miscellaneous Soffit Vent
One-piece Soffit Vent designed for plywood, soffit board, and three-coat stuccoMay be combined with Starter Strips / Casing Beads or DEFS Casing Beads.
Surface Mount Soffit Vent
One-piece soffit board designed for venting soffit areas over exterior board in EIFS and DEFS applicationsAvailable with 2", 3", 4" wide vents, each with a 1/8” ground. Vent clips are provided to…
Soffit Vent with Perforated Flanges
Provides an economical means for venting soffit areasOne-piece soffit vent with perforated flanges to assist in embedment of the base coat mixture and to cover the raw edges of the soffit board. Vent…
Soffit Drip - Surface Mount
Designed for exterior soffits where a drip screed and an edge reveal need to be combinedUsed to direct moisutre away from the installation in EIFS and DEFS installations. Always use a rigid backing…
Soffit Drip - Pre-Installed
Designed for exterior soffits where a drip screed and edge reveal need to be combinedPre-installed soffit edge reveals with a drip edge to direct moisture away from the installation.
Vented Shadow Reveal
Designed for ceilings when a vented reveal is required at the juncture of a wall and ceiling where horizontal movement may occurVent clips are provided to connect reveal sections and to assist in…
Vented Channel Reveal - Surface Mount
Vented Channel Reveals facilitate perimeter air flow to assist in moisture management and temperature controlThis vent is intended for surface-mount applications. Always use a rigid backing or…
Paper-Faced L-Trim
Protects and finishes wallboard edge when gypsum panels abut dissimilar surfacesL-Trims are used to finish the ends of wallboard where it abuts dissimilar surfaces such as suspended ceilings, beams,…