Search
Products
BlazeFrame® (SL 1)
BLAZEFRAME (SL 1) SLOTTED one SIDEProfile with one slotted leg and one solid leg w/ firestop on slotted side. Composite Firestop Deflection Track System for use in fire rated wall assemblies.…
BlazeFrame® RipTRAK™ Shaftwall
head-of-wall deflection track - 1 & 2 hour systemBlazeFrame RipTRAK Shaftwall is a ceiling runner with an offset shoulder that represents the thickness of the wall material (5/8"…
093 Zinc Control Joint (ZNCJ)
Drywall or veneer plaster control jointClarkDietrich 093 Zinc Control Joint is applied between abutting gypsum panels and is used to relieve the stresses of expansion and contraction of drywall and…
Zinc Control Joints #38, #50 & #75
Resists corrosion on applications of plaster and stucco
A solid flange zinc control joint that resists corrosion on interior and exterior applications of plaster and stucco. The #38, #50 & # 75…
ClarkDietrich Shaftwall Systems
Fully tested and approved assemblies for shaftwall constructionProvides maximum flexibility to choose from a variety of board manufacturers.
Zinc Mini-Bead™ 800 and 900
Corner reinforcementZinc Mini-Bead™ 800 and 900 are fine-mesh corner beads used to provide corner reinforcement for one-coat and two-coat veneer plaster systems. 1-1/4" wide fine-mesh flanges…
#701B/#801B L-Trim
Applied after panel installation to finish veneer plaster edges at wall terminationsVeneer trims 701B and 801B are L-shaped trims designed for use at junctions of veneer gypsum base with rough…
BlazeFrame® (DL 1)
BLAZEFRAME (DL 1) deep legProfile with two solid legs w/ firestop on one side. Composite Firestop Deflection Track System for use in fire rated wall assemblies. Two solid legs supporting “free…
BlazeFrame® (JR 1)
BLAZEFRAME (JR 1) Shaftwall deep legProfile with two solid legs with fire stop on one side. Composite Firestop Deflection Track System for use in up to 2 hr rated shaft wall assemblies. One leg…
BlazeFrame® Perimeter L-Bead
VINYL L-Bead with Compressible FoamCreates an easy attachment that is attained with staples through the bead flange.
#701A/#801A Zinc J-Trim
Provides clean, neat edge protection at gypsum panel terminations for one- and two-coat veneer plaster finishes
Veneer trims 701A and 801A are J-shaped trims formed from Zinc Alloy to fit standard 1…
Light and Medium Framing Angle
Light and Medium Framing AngleCDFA's provide fast, accurate bolting of two intersecting wood members (reinforcing intersection joints).
Gusset Clips
GUSSET CLIPSA one-piece design provides 3-way connection (top-bottom-side) for a variety of applications.
"L" and "T" Strap Ties
"l" and "T" strap tiesEconomical braces are ideal for gates, patio covers, joining posts and columns to headers, beams and other applications where added reinforcement is needed.
Medium Clip Angle
Medium clip angle12 gauge angles used to attach back-to-back installation.
#701B/#801B Zinc L-Trim
Applied after panel installation to finish veneer plaster edges at wall terminations
Veneer trims 701B and 801B are L-shaped trims designed for use at junctions of veneer gypsum base with rough…
Framing Angles
light and medium framing anglesCDFA's provide fast, accurate bolting of two intersecting wood members (reinforcing intersection joints).
Mending Tie Plate
MENDING TIE PLATESVersatile and easy-to-use mending plates for wood-to-wood connections.
Nail Stop Plates
nail stop PLATESDesigned to prevent nails from piercing and damaging mechanical, electrical and plumbing pipes and lines.
Steel Plywood/Sheathing Clip
steel plywood / sheathing clipFast and easy - just slip over the sheathing edge. Eliminates unreliable wood blocking.
Twist Straps (CDLST Series)
TWIST STRAPSManufactured to resist tension load when attached to solid sawn or structural composite lumber metal plate connected trusses, framing members and wall members.
Tie Plate Anchor Series (CDTPA)
TIE PLATE ANCHOR SERIESThe CDTPA Anchor Series is manufactured to resist uplift of the top plate(s) of solid sawn or structural composite lumber wall members from solid sawn or structural composite…
Nail Plates
nail PLATESNail Plates are used for attaching wooden members together in a non-structural connection.
Light Straps (CDLS Series)
Light STRAPSManufactured to resist tension load when attached to solid sawn or structural composite lumber metal plate connected trusses, framing members and wall members.
Medium Straps (CDLMS Series)
Medium STRAPSManufactured to resist tension load when attached to solid sawn or structural composite lumber metal plate connected trusses, framing members and wall members.
Straps (CDMS Series)
STRAPSManufactured to resist tension load when attached to solid sawn or structural composite lumber metal plate connected trusses, framing members and wall members.
Rolled Straps
rolled STRAPSManufactured to resist tension load when attached to solid sawn or structural composite lumber metal plate connected trusses, framing members and wall members.
#701A/#801A J-Trim
Provides clean, neat edge protection at gypsum panel terminations for one- and two-coat veneer plaster finishesVeneer trims 701A and 801A are J-shaped trims formed from galvanized steel to fit…
Mini-Bead™ 800 and 900
Provides superior keying for joint compound for one-coat plaster veneer systemsMini-Bead™ 800 and 900 are fine-mesh corner beads used to provide corner reinforcement for one-coat and two-coat…