Search
Products
Mini-Bead™ 800 and 900
Provides superior keying for joint compound for one-coat plaster veneer systemsMini-Bead™ 800 and 900 are fine-mesh corner beads used to provide corner reinforcement for one-coat and two-coat…
E-Screen (Drainage Mat)
Rainscreen Drainage MatClarkDietrich E-Screen can be used in stucco, stone veneer, brick, or under various siding installations to provide an effective method for drainage and ventilation in the wall…
#701A/#801A J-Trim
Provides clean, neat edge protection at gypsum panel terminations for one- and two-coat veneer plaster finishesVeneer trims 701A and 801A are J-shaped trims formed from galvanized steel to fit…
#701B/#801B L-Trim
Applied after panel installation to finish veneer plaster edges at wall terminationsVeneer trims 701B and 801B are L-shaped trims designed for use at junctions of veneer gypsum base with rough…
Cornerite™
Reinforcement for inside or outside cornersCornerite™ reinforcing angle is used to reinforce all inside or inner plaster corners to reduce corner cracking. Cornerite reinforcing angle is formed from…
Vinyl 3-1/2" Drip Screed w/ Weep Holes and Tape
Relieves moisture from stucco
The DS15-78-25WX is a combination Drip Screed with Casing Bead and Control Joint for use in stucco plane transitions. Install on frame construction for use in…
Soffit Drip - Pre-Installed
Designed for exterior soffits where a drip screed and edge reveal need to be combined
Pre-installed soffit edge reveals with a drip edge to direct moisture away from the installation.
Sloped Sill Wedge
Trim component used to provide a slope over the sill to direct intruding water to the outside of the weather-resistive barrier
This is not a flashing; it is intended for use in combination with…
Drip Casing
Drip leg directs moisture away from openings and foundation walls
Designed to be used above window and door openings or at the foundation line to assist with moving moisture away from the wall. May…
Drip Flashing - 3" and 3-1/2" Flange
Designed to be used above window and door openings or at the foundation line
To assist with moving moisture away from the wall.
Truss Spacer / Bracer
TRUSS SPACER / BRACER
The Truss Spacer/Bracer is used for lateral bracing and spacing of trusses 24 inches on center.
Load Share Clip (CDLSC)
LOAD SHARE CLIP
The CDLSC load share clip series is manufactured to transfer loads between two truss or framing ply members made of solid sawn or structural composite lumber.
Hurricane Anchor Clips
HURRICANE ANCHOR CLIPS
The CDHTHA anchor series is manufactured to attach metal plate connected trusses, framing members and wall members, made of solid sawn or structural composite lumber; to solid…
Hurricane Tie (CDHT2A, 2.5A, 2.5T, 3)
HURRICANE tie
Used as a connection between truss/rafters and walls to resist lateral and uplift conditions.
Hurricane Tie (CDHT6, 8)
HURRICANE tie
Used as a connection between truss/rafters and walls to resist lateral and uplift conditions.
Hurricane Tie (CDHT1, 10A, 10S)
HURRICANE tie
Designed to hold trusses on both sides to transfer uplift loads from roof framing members to the wall studs.
Connector Clips (for Control Joints)
Designed to assist in the alignment of control joints
And to provide a base for caulking.
Straight and Mitered Connector Clips (for Soffit Vents)
Assists in the alignment of soffit vents
Connects multiple sections.
Connector Clips (for Channel Reveals)
Designed to be used with channel reveals as a base for sealants
And to assist in alignment.
F40 (Female Casing Expansion Joint Compound)
Female casing bead with an expansion slot
Used as a component of expansion joints, vents, reveals, etc.
M40 (Male Casing Expansion Joint Compound)
Male casing bead, used as a component expansion joints
May be used as a drip reveal or a slotted reveal, etc.
M50 (Wide Male Casing Expansion Joint Compound)
Wide male casing bead, used as a component expansion joints
May be used as a drip reveal or a slotted reveal, etc.
F50 (Wide Female Casing Expansion Joint Compound)
Wide female casing bead with an expansion slot
Used as a component of expansion joints, vents, reveals, etc.
Colored Vinyl
Color LeadershipIn addition to our standard white vinyl accessories, we’ve taken the lead in stocking vinyl accessories in tan, brown, gray and black that perfectly complement common mortar colors.
Factory Fabricated Channel Reveals
Create clear channel designs for drywall surfacesAll intersections are manufactured in a controlled factory environment to the highest quality standards.
Factory Fabricated Vinyl Control Joints
Control joint intersections are manufactured in a controlled factory environment to the highest quality standardsMiter cuts are made with precision to ensure proper fit at all connections.
BackerBead® Drip Flashing - 3-1/2" Flange
Drip flashing with built-in closed cell backer rodBackerBead® Drip Flashing - 3-1/2" Flange is designed to provide positive drainage above exterior window and door openings while also providing a…
Archmaker™ Drip Flashing - 2" Flange
Designed to be used above window and door openings or at the foundation lineTo assist with moving moisture away from the wall.
DS15 Drip
Used with drip screed and as drip in special conditionsSuch as soffits, balconies, etc.