Search
Products
Foundation Weep Screed
Moisture removal from stucco
Acts as a stop, and is designed with an unperforated flange to allow moisture removal from stucco installations on frame construction at the foundation line.
Furring Channel / Hat Channel
Furring Channel for Walls and Ceilings
Economical hat-shaped framing component used to “furr” out ceilings and masonry walls.
L-Angle / Corner Angle
L-angle / corner angle
Non-structural corner angles commonly used to connect, reinforce or secure metal stud framing in various drywall applications.
Structural L-Angle commonly used for connection…
U-Channel (CRC)
Traditional cold-rolled Channel (CRC) for bridging
ClarkDietrich U-Channel or Cold Rolled Channel (CRC) are one of the most common bridging methods used to provide resistance to stud rotation and…
Light and Medium Framing Angle
Light and Medium Framing Angle
CDFA's provide fast, accurate bolting of two intersecting wood members (reinforcing intersection joints).
Gusset Clips
GUSSET CLIPS
A one-piece design provides 3-way connection (top-bottom-side) for a variety of applications.
Medium Clip Angle
Medium clip angle
12 gauge angles used to attach back-to-back installation.
Framing Angles
light and medium framing angles
CDFA's provide fast, accurate bolting of two intersecting wood members (reinforcing intersection joints).
Mending Tie Plate
MENDING TIE PLATES
Versatile and easy-to-use mending plates for wood-to-wood connections.
Nail Stop Plates
nail stop PLATES
Designed to prevent nails from piercing and damaging mechanical, electrical and plumbing pipes and lines.
Steel Plywood/Sheathing Clip
steel plywood / sheathing clip
Fast and easy - just slip over the sheathing edge. Eliminates unreliable wood blocking.
Twist Straps (CDLST Series)
TWIST STRAPS
Manufactured to resist tension load when attached to solid sawn or structural composite lumber metal plate connected trusses, framing members and wall members.
Tie Plate Anchor Series (CDTPA)
TIE PLATE ANCHOR SERIES
The CDTPA Anchor Series is manufactured to resist uplift of the top plate(s) of solid sawn or structural composite lumber wall members from solid sawn or structural composite…
Nail Plates
nail PLATES
Nail Plates are used for attaching wooden members together in a non-structural connection.
Light Straps (CDLS Series)
Light STRAPS
Manufactured to resist tension load when attached to solid sawn or structural composite lumber metal plate connected trusses, framing members and wall members.
Medium Straps (CDLMS Series)
Medium STRAPS
Manufactured to resist tension load when attached to solid sawn or structural composite lumber metal plate connected trusses, framing members and wall members.
Straps (CDMS Series)
STRAPS
Manufactured to resist tension load when attached to solid sawn or structural composite lumber metal plate connected trusses, framing members and wall members.
Rolled Straps
rolled STRAPS
Manufactured to resist tension load when attached to solid sawn or structural composite lumber metal plate connected trusses, framing members and wall members.
Vinyl 3-1/2" Drip Screed w/ Weep Holes and Tape
Relieves moisture from stucco
The DS15-78-25WX is a combination Drip Screed with Casing Bead and Control Joint for use in stucco plane transitions. Install on frame construction for use in…
CI Weep Track
Directs water drainage
Designed to be used with #1 Corner Bead around windows and doors and at the foundation line.
#36 Sill Screed
Exterior Foundation sill screed
A variation of the #7 style screed which allows trowel access underneath the screed to clean excess stucco material. No visible metal is seen below the stucco line.
FHA-7 Weep Sill Screed
Exterior foundation WEEP (sill) screed
The FHA-7 is for hard-coat stucco, thin-veneer stone, and 1-coat stucco over foam applications. Installed at the juncture of the sill and the exterior…
3-1/2" J-Weep High-Back
Used as sill weep screed or at door and window opening
J-Weep High-Back Plaster Stop is a J-shaped, square-nosed trim manufactured from 26-gauge galvanized steel. The 1-3/8" ground is designed for…
Positive Drain Weep Screed
Designed to provide a flashing transition
From stucco, siding, stone over a brick ledge, at a wall transition.
Mid Wall Weep Screed - M Style
Screed with built-in control joint
Accomodates expansion/contraction of the separate substrates.
Mid Wall Weep Screed with Weep Holes/Tape
Designed to relieve stress and assist in controlling cracks in exterior wall finish
Have built-in control joint to accommodate expansion/contraction of the separate substrates.
2" (Nominal) J-Weep Low-Back
Used as a casing stop bead with stucco, stone and E.I.F.S. Systems
2" Nominal J-Weep Low-Back (2-inch back flange) is commonly used as a straight edge plaster stop at the top of doors and windows…
Structural Studs
ClarkDietrich Cold-Formed Steel C-Studs (C-Series™)Cold-Formed / Light-Gauge C-shaped framing members for axial load-bearing walls, curtain walls, tall interior partitions, floor joists and roof…
Structural Track
ClarkDietrich Cold-Formed Steel TrackU-shaped channel runners used as the top and bottom tracks to secure wall studs or end support closures for floor joist framing. Structural Steel Track can be…
PanelTRAK
Steel Track for direct web bearingPanelTRAK is a structural steel track that allows steel studs to bear directly on the track web rather than the radii of the track corners. Because…
1-3/4" Weep Screeds (Perforated Flange)
Designed to direct moisture from stucco and to act as a stopInstall on masonry construction where stucco and foundation walls meet.
1-3/4" Weep Screeds (Unperforated Flange)
Designed to direct moisture from stucco and to act as a stopInstall on frame construction where stucco and foundation walls meet.
3-1/2" Weep Screeds
Designed to direct moisture from stucco and to act as a stopInstall on frame construction where stucco and foundation walls meet.
1/4" Drip "V" Screeds
Designed for stucco or plaster soffits when drip and reveal need to be combined
"L" and "T" Strap Ties
"l" and "T" strap tiesEconomical braces are ideal for gates, patio covers, joining posts and columns to headers, beams and other applications where added reinforcement is needed.
Z-Girt for Rainscreen Framing
Z Girt for Rainscreen FramingGalvanized Z-Girt with standard depths to match common exterior insulation thicknesses. Can be installed in a vertical or horizontal orientation to accommodate…