Search

The CDTBR24 is made from high-strength steel to meet the industry’s most demanding engineering standards. It was designed from the ground up to solve field installation problems. The Truss Spacer/Bracer is used for lateral bracing and spacing of trusses 24 inches on center.

The CDTBR24 meets BCSI-B2 Truss Installation & Temporary Restraint/Bracing requirements, with values that exceed the competition in every installation configuration. To eliminate potential safety issues, the edges have been rolled and the tabs are inverted for easy installation.

Material: 24 gauge (23mil) 0.0238" Design thickness, 0.0227" Minimum thickness
Coating: G90 (Z275) hot-dipped galvanized coating
Yield Strength: Structural Grade 50 Type H (ST50H), 50ksi (340 MPa)

Product Dimensions

Length (L): 25-9/16"
Width (W): 1-1/2"
Depth (D): 5/8"

CDAGUS universal face-mount hanger is designed for wood plate trusses and heavily loaded members. 4" seat dimension provides greatest bearing area of any hanger available. Super capacity design loads are the highest of any universal face-mounted hanger. Larger header flange and joist seat make this hanger very easy to install with common nails.

PRODUCT DIMENSIONS

Joist and Truss Sizes: 2xs, double 2xs, triple 2xs
Material: 12ga (97mil), 0.1017" Design thickness, 0.0966" Minimum thickness
Coating: G90 (Z275) hot-dipped galvanized coating
Yield Strength: Structural Grade 50 Type H (ST50H), 50ksi (340 MPa)

Designed specifically for agricultural and post-frame use with superior performance and easy installation. All of the hangers offer multiple installation methods, giving users maximum flexibility. Double-shear and straight nailing options available. Placement tooth or placement nail options for simplified installation.

Material: 18ga (43mil), 0.0451" Design thickness, 0.0428" Minimum thickness
Coating: G90 (Z275) hot-dipped galvanized coating
Yield Strength: Structural Grade 50 Type H (ST50H), 50ksi (340 MPa)

PRODUCT DIMENSIONS

D11-3/4"
D21-9/16"
H1-9/16"
D1-9/16"

The CDLEHJ accommodates an end jack and a right or left hip jack. Made from high strength steel, this hanger offers a high load capacity while requiring only half as many fasteners in the header. It is designed to be installed with the same length fastener in all members (10d x 1-1/2") unlike competitive products which require 3" fasteners in the header to achieve the stated loads.

Material: 18ga (43mil), 0.0451" Design thickness, 0.0428" Minimum thickness
Coating: G90 (Z275) hot-dipped galvanized coating
Yield Strength: Structural Grade 50 Type H (ST50H), 50ksi (340 MPa)

   Overall Dimensions (in)Common Nail Type Fasteners
Product CodeMin. Supporting MemberMin. Supported End
and Hip Jack Height		WidthHeightDepthSize (in)End Jack QtyHip Jack Qty.Header Qty.
CDLEHJ2 x 63.507.765.254.87510d x 1.54610

Note: For SI: 1in. = 25.4mm, 1lb. = 4.45 N
1 See images for hanger dimensions.
2 Refer to section 3.2.3 of ESR-5062 code report for nail sizes and the required minimum physical properties.

Manufactured to resist tension load when attached to solid sawn or structural composite lumber metal plate connected trusses, framing members and wall members. ClarkDietrich Rolled Strapping (CDRS) are 1-1/4" wide with holes punched at 1-1/4" on center, in a staggered pattern. Strapping is manufactured in continuous rolls of 250 feet for 20 gauge, 200 feet for 18 gauge and 150 feet for 16 gauge.

CDRS150
Material: 16ga (54mil), 0.0566" Design thickness, 0.0538" Minimum thickness
Coating: G90 (Z275) hot-dipped galvanized coating (G185 available)
Yield Strength: Structural Grade 50 Type H (ST50H), 50ksi (340 MPa)

CDRS200
Material: 18ga (43mil), 0.0451" Design thickness, 0.0428" Minimum thickness
Coating: G90 (Z275) hot-dipped galvanized coating
Yield Strength: Structural Grade 50 Type H (ST50H), 50ksi (340 MPa)

CDRS250
Material: 20ga (33mil), 0.0346" Design thickness, 0.0329" Minimum thickness
Coating: G90 (Z275) hot-dipped galvanized coating
Yield Strength: Structural Grade 50 Type H (ST50H), 50ksi (340 MPa)

 

 

 

Product CodeWidth (in)Length (ft)
CDRS1501-1/4"150'
CDRS2001-1/4"200'
CDRS2501-1/4"250'

 

Manufactured to resist tension load when attached to solid sawn or structural composite lumber metal plate connected trusses, framing members and wall members.

CDMS Straps are 1-1/4" wide and available in lengths from 21-5/8" to 39-5/8". Three holes are located at 3/4" on center, in a diagonal pattern, at each end of the strap. Remaining holes are punched at 1-1/2" on center, in a diagonal pattern. At mid length of each strap is a 3" long section with no holes.

Material: 16ga (54mil), 0.0566" Design thickness, 0.0538" Minimum thickness
Coating: G90 (Z275) hot-dipped galvanized coating (G185 available except on CDMS27, CDMS33 & CDMS39)
Yield Strength: Structural Grade 50 Type H (ST50H), 50ksi (340 MPa)

 

 Strap Dimensions (in)
Product CodeWL
CDMS211-1/421-5/8
CDMS241-1/424-5/8
CDMS271-1/427-5/8
CDMS301-1/430-5/8
CDMS331-1/433-5/8
CDMS361-1/436-5/8
CDMS391-1/439-5/8

 

Manufactured to resist tension load when attached to solid sawn or structural composite lumber metal plate connected trusses, framing members and wall members.

CDLMS Medium Straps are 1-1/4" wide and available in lengths from 9-5/8" to 36-5/8". Three holes are located at 3/4" on center, in a diagonal pattern, at each end of the strap. Remaining holes are punched at 1-1/2" on center, in a diagonal pattern. At mid length of each strap is a 3" long section with no holes.

Material: 18ga (43mil), 0.0451" Design thickness, 0.0428" Minimum thickness
Coating: G90 (Z275) hot-dipped galvanized coating (G185 available except CDLMS33)
Yield Strength: Structural Grade 50 Type H (ST50H), 50ksi (340 MPa)

 Strap Dimensions (in)
Product CodeWL
CDLMS91-1/49-5/8
CDLMS121-1/412-5/8
CDLMS151-1/415-5/8
CDLMS181-1/418-5/8
CDLMS211-1/421-5/8
CDLMS241-1/424-5/8
CDLMS301-1/430-5/8
CDLMS331-1/433-5/8
CDLMS361-1/436-5/8

 

Manufactured to resist tension load when attached to solid sawn or structural composite lumber metal plate connected trusses, framing members and wall members.

CDLS Light Straps are 1-1/4" wide and available in lengths from 9-5/8" to 24-5/8". Three holes are located at 3/4" on center, in a diagonal pattern, at each end of the strap. Remaining holes are punched at 1-1/2" on center, in a diagonal pattern. At mid length of each strap is a 3" long section with no holes.

Material: 20ga (33mil), 0.0346" Design thickness, 0.0329" Minimum thickness
Coating: G90 (Z275) hot-dipped galvanized coating
Yield Strength: Structural Grade 33 Type H (ST33H), 33ksi (227.5 MPa)

 Light Strap Dimensions (in)
Product CodeWL
CDLS91-1/49-5/8
CDLS121-1/412-5/8
CDLS151-1/415-5/8
CDLS181-1/418-5/8
CDLS211-1/421-5/8
CDLS241-1/424-5/8

 

Nail Plates are used for attaching wooden members together in a non-structural connection.

Material: 20ga (33mil), 0.0346" Design thickness, 0.0329" Minimum thickness
Coating: G90 (Z275) hot-dipped galvanized coating
Yield Strength: Structural Grade 50 Type H (ST50H), 50ksi (340 MPa)

Product CodeSize
CDNP152" X 5"
CDNP353" X 5"
CDNP373" X 7"
CDNP454" X 5"
CDNP474" X 7"
CDNP575" X 7"
CDNP15-Dims
CDNP35-Dims
CDNP37-Dims
CDNP45-Dims
CDNP47-Dims
CDNP57-Dims

The CDTPA Anchor Series is manufactured to resist uplift of the top plate(s) of solid sawn or structural composite lumber wall members from solid sawn or structural composite lumber wall stud members.

CDTPA4 and CDTPA6 anchors resist upward load on nominal 2x4 and 2x6 respectively, solid sawn or structural composite lumber walls.

Material: 20ga (33mil), 0.0346" Design thickness, 0.0329" Minimum thickness
Coating: G90 (Z275) hot-dipped galvanized coating
Yield Strength: Structural Grade 50 Type H (ST50H), 50ksi (340 MPa)

Product CodeGaugeWidthHeightDepth
CDTPA4203.56257.52651.25
CDTPA6205.56258.06251.25

 

Subscribe to