Skip to main content

Search

Strait-Flex Wide-Flex

FINISHES INSIDE AND outside 90° AND OFF-ANGLE CORNERS

Strait-Flex Wide-Flex is a mud-on, paper-faced composite corner bead that adjusts to any angle to create perfect inside and outside 90° and off-angle corners.

Application(s): Drywall

This 4” tape features a pre-finished surface with a PUR–laminated nose ensuring perfect corners without paper fuzz-up during finishing and sanding. The tape's outer edge features a diamond punch pattern for a superior bond, faster drying, with no rippling or blistering.

  • Outside corners where large gaps in drywall are present.
  • Outside corners for double 5/8" drywall.
  • Hard-to-straighten outside corners, hard-to-straighten vaulted ceilings.
  • Great for vaulted, coffered, tray and cathedral ceilings.

Installation

Make sure the surfaces of the corner are clean and smooth. Measure corner and subtract 1/2”. (1) For accurate measuring of Strait-Flex® Wide-Flex and less waste, feed roll through slot on top of box. Hook tape measure on the hole below. (2) Fold Wide-Flex in half with the print side facing out. (3) For outside corners, fold more than the desired angle. For inside corners, fold less than desired angle. (4) Most professionals prefer to cut the ends of Wide-Flex at a 45º angle.

(5)  Apply a liberal coat of all-purpose joint compound to both sides of the corner with a 4” or 5” taping knife.  (6) Press Wide-Flex into the wet compound. Adjust, if necessary, to create a straight line. (7) Wipe down tight with taping knife using a little additional pressure on the outer edges. Let dry completely over several hours or overnight.

(8) Apply a light skim coat of compound to the outer edges of Wide-Flex with a 4” or 5” taping knife. No compound is required over the laminated area of Wide-Flex. Wipe down tight and smooth. Let dry completely over several hours or overnight.

(9) Apply the final coat of joint compound with a 6” or 8” taping knife. Feather the compound beyond previous coat. A very light coat of compound is all that’s needed. Using lightweight compound in this step makes sanding easier. Let dry completely over several hours or overnight.

(10) Sand lightly with 120 grit sandpaper. Wide-Flex will not fuzz-up like paper or mesh tapes.

INSTRUCCIONES DE INSTALACIÓN

Asegúrese de que las superficies de la esquina estén limpias y lisas. Mida la esquina y reste 1/2". (1) Para medir el Strait-Flex® Wide-Flex con más precisión y menos desperdicio, inserte la cinta a través de la ranura en la parte superior de la caja. Enganche la cinta métrica en el agujero que está debajo. (2) Doble el Wide-Flex por la mitad con la cara impresa hacia fuera. (3) Para esquinas externas, doble a un ángulo mayor al deseado. Para esquinas internas, doble a un ángulo menor al deseado. (4) La mayoría de los profesionales prefieren cortar los extremos del Wide-Flex a un ángulo de 45º.

(5) Aplique una capa generosa del compuesto multiusos para juntas en ambos lados de la esquina con una espátula de 4" o 5".  (6) Presione el Wide-Flex sobre el compuesto húmedo. Si es necesario, ajuste para crear una línea recta. (7) Raspe con la espátula para que quede al ras, usando un poco más de presión sobre los bordes externos. Permita que se seque completamente, por varias horas o durante la noche.   

(8) Aplique una capa ligera del compuesto a los bordes exteriores del Wide-Flex con una espátula de 4" o 5". No necesita aplicar compuesto sobre las áreas laminadas del Wide-Flex. Raspe para que quede lisa y al ras. Permita que se seque completamente, por varias horas o durante la noche.   

(9) Aplique la capa final del compuesto para juntas con una espátula de 6" o 8". Raspe el compuesto hasta cubrir completamente la capa anterior. Una capa muy ligera del compuesto es todo lo que necesita. Usar un compuesto más ligero en este paso, hace que sea más fácil de lijar. Permita que se seque completamente, por varias horas o durante la noche.

(10) Lije ligeramente con papel de lija grano 120. Wide-Flex no hace pelusa como sucede con las cintas de papel o malla.

Code Approvals & Performance Standards

Storage:

All stored materials shall be kept dry. Materials shall be stacked off the ground, supported on a level platform, and protected from weather and moisture.

Product Submittal Sheets

Click the below Product Code to view Submittal/Tech Datasheet.

Product Code Description
WF-100 Strait-Flex® Wide-Flex

ClarkDietrich SubmittalPro®

Submittal sheets for the exact product you're looking for can be created by using ClarkDietrich's SubmittalPro® Product Submittal System.